Difference between revisions of "Shellcode/Environment"

Revision as of 09:55, 26 November 2012

It is possible use shellcode to determine instruction set architecture, determine the process counter, determine the location last returned to, or bypass and detect int3 breakpoints within the current execution environment.

The code and ideas discussed here are part of an all-encompassing shellcode portal. Everything described here and the full source of any given code is available in the appendix, as well as in the downloadable shellcodecs package.

x86/x64 GetCPU (any OS)

Architecture can only be determined when compatible channels between the target instruction set architectures can be isolated. As long as the instructions perform valid behavior and do not cause access faults on operating systems native to the architecture, it is possible to use a single bytecode sequence in order to determine architecture across a variety of processors. It takes a high amount of familiarity and experience with two or more given instruction sets to write shellcode for multiple architectures.

x64 does not vastly differ from x86 because AMD stepped in to correct intel's calling convention and architecture.

Instruction Comparison

This chart was derived by cross referencing available alphanumeric 64 bit instructions with available printable 32 bit instructions.

Inter-compatibility theory

The opcodes which are specifically not compatible are limited to the 32 and 64 bit opcodes 0x40-0x4f, which allow a 32 bit processor to increment or decrement its general-purpose registers, but become prefixes for manipulation of 64 bit registers and 8 additional 64 bit general purpose registers in x64 environments, %r8-%r15.

Because not all opcodes are intercompatible, yet comparisons and conditional jumps are intercompatible, it is possible to determine the architecture of an x86 processor using exclusively alphanumeric opcodes.

By making use of these additional registers (which 32 bit processors do not have), one can perform an operation that will set a value on a different register in the two processors.

Following this, a conditional statement can be made against one of the two registers to determine if the value was set.

Using the pop instruction is the most effective way to set the value of a register due to instructional limitations (to keep the code alphanumeric). Using an alternative register to %rsp or %esp as a placeholder for the stack pointer enables the use of an effective conditional statement to determine if the value of a register is equal to the most recent thing pushed or popped from the stack.

Practically Applied: Code

This simple alphanumeric bytecode is 15 bytes long, ending in a comparison which returns equal on a 32 bit system and not equal on a 64 bit system.

When implementing this bytecode, a conditional jump afterwards may be best reserved for the t and u instructions, jump if equal and jump if not equal, respectively.

• Assembled:

TX4HPZTAZAYVH92

• Disassembly:

push %esp

push %rsp

pop %eax

pop %rax

xor $0x48, %al

xor $0x48, %al

push %eax

push %rax

pop %edx

pop %rdx

push %esp

push %rsp

inc %ecx
pop %edx

pop %r10

inc %ecx
pop %ecx

pop %r9

push %esi

push %rsi

dec %eax
cmp %esi,(%edx)

cmp %rsi,(%rdx)

This code executes similarly on both a 32-bit and 64-bit system - similarly, but not identically. The key discrepancy between how the two architectures execute this code is contained in the opcodes "0x41 - 0x4f".

Under a 32-bit architecture, this code pops the value of esp (which was pushed onto the stack previously) into edx and increments ecx. The esp register is a pointer to the top of the stack, so now rdx contains a pointer to the top of the stack. After this is done, the shellcode goes on to push esi onto the stack - so the value of esi now resides at the top of the stack. When the code executes its final comparison - "cmp %esi, (%edx)" - it is comparing the value of esi to the value that edx points to. As edx points to the top of the stack, and as we have just pushed esi onto the top of the stack, we are comparing the value of esi with the value of esi. For this reason, it returns equal.

This shellcode is not equal under a 64-bit architecture, however. The opcodes "41 5a 41 59" have a different function - instead of popping the value of esp into rdx, it instead pops it into the 64-bit register %r10 without incrementing %ecx or %rcx, as 0x41 is used as a prefix to indicate the access to the 64-bit architecture. As a result, when the final comparison is made between rsi and the value referenced by rdx, it returns not equal, as rdx does not point to the top of the stack.

On a 64-bit system, this will not cause a segfault because (%rdx) points to somewhere inside the stack.

GetPc

The GetPc technique is any technique implementing code which obtains the current instruction pointer. This can be useful when writing polymorphic shellcode, or other code that must become aware of its environment because environment information cannot be supplied prior to execution of the code.

x86 (32 bit)

 
jmp startup
getpc:
   mov (%esp), %eax
   ret
startup:
call getpc       ; the %eax register now contains %eip on the next line 
 

x64

 
jmp startup
getpc:
   mov (%rsp), %rax
   ret
startup:
call getpc       ; the %rax register now contains %rip on the next line 
 

Last call

Typically, when shellcode is being executed at the time of overflow, assuming that the nop sled does not modify the stack, the pointer to the beginning of the executing code is at -0x8(%rsp), or -0x4(%esp), because it was just returned to. In many cases, this can be used in place of a getPc for polymorphic code.

32-bit

 
  mov -0x4(%esp), %eax
 

64-bit

 
  mov -0x8(%rsp), %rax
 

Alphanumeric

• Assembled x64:

 XTX4e4uHcp4H3p4H30

 
.text
.global _start
_start:
  pop %rax
  push %rsp
  pop %rax
  xor $0x65, %al
  xor $0x75, %al
  movslq 0x34(%rax), %rsi
  xor 0x34(%rax), %rsi
  xor (%rax), %rsi
 

int3 breakpoints

 
.text
.global _start
_start:
 
  jmp startup
 
go_retro:
  pop %rcx
  inc %rcx
  jmp *%rcx
 
startup:
  call go_retro
 
volatile_segment:
  push $0x3458686a
  push $0x0975c084
  nop
 

 {} shellcode gdb loaders/loader-64                                                                       
 Reading symbols from /home/user/loaders/loader-64...(no debugging symbols found)...done.
 (gdb) break ret_to_shellcode 
 Breakpoint 1 at 0x4000b1

 (gdb) run "$(generators/shellcode-generator.py --file=int3 --raw)"
 Starting program: /home/user/loaders/loader-64 "$(generators/shellcode-generator.py --file=int3 --raw)"
 
 Breakpoint 1, 0x00000000004000b1 in ret_to_shellcode ()
 (gdb) x/24i $rax
  0x7ffff7fbe000:	jmp    0x7ffff7fbe008
  0x7ffff7fbe002:	pop    %rcx
  0x7ffff7fbe003:	inc    %rcx
  0x7ffff7fbe006:	jmpq   *%rcx
  0x7ffff7fbe008:	callq  0x7ffff7fbe002
  0x7ffff7fbe00d:	pushq  $0x3458686a
  0x7ffff7fbe012:	pushq  $0x975c084
  0x7ffff7fbe017:      nop
  ...
 (gdb) break *0x7ffff7fbe017
 Breakpoint 2 at 0x7ffff7fbe017
 (gdb) c
 Continuing.
 
 Breakpoint 2, 0x00007ffff7fbe017 in ?? ()
 (gdb) quit
 A debugging session is active.
 

Inferior 1 [process 9760] will be killed.

 Quit anyway? (y or n) y

 {} shellcode gdb loaders/loader-64
 Reading symbols from /home/user/loaders/loader-64...(no debugging symbols found)...done.
 (gdb) break ret_to_shellcode 
 Breakpoint 1 at 0x4000b1
 (gdb) run "$(generators/shellcode-generator.py --file=int3 --raw)"
 Starting program: /home/user/loaders/loader-64 "$(generators/shellcode-generator.py --file=int3 --raw)"
 Breakpoint 1, 0x00000000004000b1 in ret_to_shellcode ()
 (gdb) x/24i $rax
  0x7ffff7fbe000:	jmp    0x7ffff7fbe008
  0x7ffff7fbe002:	pop    %rcx
  0x7ffff7fbe003:	inc    %rcx
  0x7ffff7fbe006:	jmpq   *%rcx
  0x7ffff7fbe008:	callq  0x7ffff7fbe002
  0x7ffff7fbe00d:	pushq  $0x3458686a
  0x7ffff7fbe012:	pushq  $0x975c084
  0x7ffff7fbe017:      nop
  ...
 (gdb) break *0x7ffff7fbe012
 Breakpoint 2 at 0x7ffff7fbe012
 (gdb) c
 Continuing.
 [Inferior 1 (process 9778) exited normally]
 (gdb)