Difference between revisions of "Gentoo Installation"
(→Hard Drive Setup) |
|||
| Line 73: | Line 73: | ||
dhcpcd eth0 | dhcpcd eth0 | ||
</pre> | </pre> | ||
| + | |||
| + | |||
| + | ---- | ||
| + | |||
| + | |||
| + | =Base installation and Configuration= | ||
| + | |||
| + | |||
| + | {{warning| Remember the number in the output of this command, you will need it later.}} | ||
| + | <pre> | ||
| + | grep -ci "processor" /proc/cpuinfo | ||
| + | </pre> | ||
| + | |||
| + | Download & Extract portage to /mnt/gentoo/usr/ | ||
| + | cd /mnt/gentoo/usr/ | ||
| + | wget http://gentoo.arcticnetwork.ca/releases/snapshots/current/portage-latest.tar.bz2 | ||
| + | tar xvjf portage-latest.tar.bz2 | ||
| + | |||
| + | Open make.conf in nano. | ||
| + | cd /mnt/gentoo/etc/ | ||
| + | nano make.conf | ||
| + | |||
| + | |||
| + | Modify make.conf as follows: | ||
| + | {{warning| Do not modify the CHOST, this will cause problems!}} | ||
Revision as of 20:11, 24 November 2011
Gentoo is a source-based linux distribution.source-based means every application is compiled locally.
You can download a copy of gentoo Here
To install gentoo you will need to create a bootable LiveCD or LiveUSB.
There are many ways one could create a LiveCD or LiveUSB, but that is outside of the scope of Gentoo Installation
Virtual Machine Setup
If you want to set up Gentoo within a virtual machine you will need at least:
- Around 512MB to 1GB of RAM
- At least 10GB HDD
- Networking features enabled
And preferably multiple cores on an x86_64 processor
Hard Drive Setup
ls /dev | grep sd cfdisk /dev/sda
cfdisk will then bring you into an ncurses gui.
Use cfdisk to:
- Create 100MB Partition Bootable at the Beginning
- Create 2048MB Partition at the beginning
- Create remaining free space partition at the beginning
Choose to Write tables to disk, and then exit.
mkfs.ext2 /dev/sda1 mkswap /dev/sda2 mkfs.reiserfs /dev/sda3 mount -t reiserfs /dev/sda3 /mnt/gentoo ; cd /mnt/gentoo wget http://gentoo.arcticnetwork.ca/releases/x86/current-stage3/stage3-i686-20110614.tar.bz2
for the below line, you can simply press the TAB button after stage3 and it will automatically complete the command, just press enter to confirm it
tar xvpjf stage3* swapon /dev/sda2 cp /etc/resolv.conf /mnt/gentoo/etc/resolv.conf
Okay, now you've set up your hard drives, downloaded a copy of gentoo on your live environment, and copied resolv.conf over.
Before continuing make sure you can access the internet.
you can test this by pinging google:
ping -c 2 google.com
if it isn't working, try the following:
|
you might need to do this each time you reboot |
ifconfig eth0 down && ifconfig eth0 up
dhcpcd eth0
Base installation and Configuration
|
Remember the number in the output of this command, you will need it later. |
grep -ci "processor" /proc/cpuinfo
Download & Extract portage to /mnt/gentoo/usr/
cd /mnt/gentoo/usr/ wget http://gentoo.arcticnetwork.ca/releases/snapshots/current/portage-latest.tar.bz2 tar xvjf portage-latest.tar.bz2
Open make.conf in nano.
cd /mnt/gentoo/etc/ nano make.conf
Modify make.conf as follows:
|
|
Do not modify the CHOST, this will cause problems! |
